Configuring Virtual Domains

Introduction

Virtual domains is the practice of hosting a service for more than one domain on one server. Cyrus IMAP has the ability to host IMAP/POP mailboxes for multiple domains (e.g., test@example.com and test@example.net) on a single server or Murder.

In order to accomplish this, Cyrus needs to know which domain to look in when a mailbox is accessed. There are two ways in which Cyrus can determine the domain:

Both of these methods are active if the virtdomains option is set to on (or yes, 1, true) and can be used in conjunction with one another. If the virtdomains option is set to userid, then only the first method is used. Note that a fully qualified userid takes precedence over a domain obtained from the IP address.

Concepts

Perhaps the most important part of this process is to understand the changes in the paradigm.

Quick Start

  1. Add virtdomains: yes to imapd.conf
  2. Add a defaultdomain entry to imapd.conf
  3. Use cyradm (as a global or domain admin) to create mailboxes for each domain.

Configuration

Support for virtual domains is enabled by turning on the virtdomains option in imapd.conf.

When upgrading from a single domain installation to a virtual domain installation, the name of the existing domain (domain of the server hostname) should be specified using the defaultdomain option in imapd.conf. This allows users to continue to access their mailboxes using unqualified userids. For example, if the primary IP address on your server resolves to 'www.xxx.yyy.zzz', then set defaultdomain to 'xxx.yyy.zzz'.

Even for new installations, it is recommended that the "real" domain of the server (domain of its primary hostname), be set to the defaultdomain. See Administrators below for further discussion.

Here is a sample imapd.conf with a minimal set of configuration options.

configdirectory: /var/imap
partition-default: /var/spool/imap
admins: admin rick.admin@hisdomain.com jill.admin@herdomain.net
virtdomains: yes
defaultdomain: exampleisp.net

This example has three domains: exampleisp.net, hisdomain.com, and herdomain.net. admin can administer all three domains, while rick.admin@hisdomain.com and jill.admin@herdomain.net can only administer their respective domains.

Note that everyday users should not be administrators. In the above example, Jill and Rick have separate administrative accounts for their domains.

Multiple IP Addresses

In order to use a multiple IP address configuration, the server must be able to do a reverse lookup on the IP address to determine the hostname of the receiving interface. For example:


192.168.0.1  ->  mail.example.com
192.168.0.2  ->  mail.example.net
192.168.0.3  ->  mail.foo.bar

Once the server obtains the fully qualified hostname of the interface, it removes the localpart (i.e., 'mail') and uses the remainder as the domain for any user that logs in.

This address to hostname mapping would usually be done via DNS, /etc/hosts, NIS, etc. Configuration of the various naming services is beyond the scope of this document.

Delivering mail

To deliver mail to your virtual domains, configure your MTA so that the envelope recipient (RCPT TO) passed to lmtpd is fully qualified with the correct domain.

Configuring Sendmail

In general, follow the basic configuration instructions. Here are a few caveats:

Mail Clients

The only changes you'll need to make to mail clients is to change usernames to the fully qualified domain names, i.e., user@example.com. Note that to support some mail clients, the user%example.com form of userid is also supported. Users in the default domain will not need to reconfigure their clients (as unqualified userids are assumed to be in the default domain).

Administration

The Cyrus virtual domains implementation supports per-domain administrators as well as "global" (inter-domain) administrators. Domain-specific administrators are specified with a fully qualified userid in the admins option (e.g., admin@example.net) and only have access to mailboxes in the associated domain. Mailbox names should be specified in the same fashion as on a single domain configuration.

Global administrators are specified with an unqualified userid in the admins option and have access to any mailbox on the server. Because global admins use unqualified userids, they belong to the defaultdomain. As a result, you CANNOT have a global admin without specifying a defaultdomain. Note that when trying to login as a global admin to a multi-homed server from a remote machine, it might be necessary to fully qualify the userid with the defaultdomain.

Global admins must use mailbox@domain syntax when specifying mailboxes outside of the defaultdomain. Examples (using cyradm):

To create a new INBOX for user 'test' in defaultdomain:


   cm user.test

To create a new INBOX for user 'test' in domain 'example.com':


   cm user.test@example.com
To list all mailboxes in domain 'example.com':


   lm *@example.com


last modified: $Date: 2008/01/07 17:56:12 $